How to set up a dir 320 modem. An old horse, it doesn’t spoil the furrow

The Dir-320 router, the brainchild of the popular company D-link, is a wireless router with a data transfer speed of 54 Mbit/s and USB 2.0 support.

Unfortunately, at present this model is practically no longer relevant, since the technical characteristics of the router - according to current demands - leave much to be desired.

Therefore, relatively recently - in 2011, the company "D-link" released the updated "Dir-320 NRU" with support for "WiMAX", "3G GSM", "CDMA" and a data transfer rate of up to 150 Mbit/s - for 2011 this is enough good performance.

Brief overview of the dir 320 router

Detailed list technical characteristics The router is shown in the following illustrations:

The router body is black with one external antenna on the right side of the router.

The indicator panel consists of 8 elements:

“Power” - power on/off;
“Internet” - if the indicator is blinking, traffic is being transmitted, if it is just “on”, the connection is established;
“Wireless network” - blinking – data is being transferred, “lit” - the network is active;
“Local network 1-4” - blinking – traffic is being transmitted over the corresponding port, “lit” - the network device is connected;
“USB” - “lit” - an external USB device is connected, flashing - the connection is established.

Rear panel router dir 320:

“LAN 1-4” - ports for connecting network devices;
“Internet” - port for connecting to an “Ethernet line” or DSL modem;
“USB” - port for connecting USB modems;
“5V-2A” - connector for connecting a power adapter;
“Reset” is a button used to reset to factory settings.

How to set up an Internet connection on a d link dir 320 router?

Prepare an agreement with your service provider in advance, as it will contain the authorization data necessary to set up an Internet connection.

To enter the router settings, you need to connect the router d link dir 320 To and enter the address 192.168.0.1 in the address bar of the browser. When prompted for a login and password, enter “admin/admin”.

If your router has been in use before, then before making settings you need to reset its configuration to the factory one using the Reset button. Otherwise, authorization errors may occur (for example, an incorrect login and password will be specified) and problems with setting up the device.

Below is appearance router interface d link dir 320 from software version “1-2-94”, which is stock by default.

After logging into the web interface for the first time, you need to change the administrator password (in order to secure the network from possible unauthorized entry), and then click the “Save” button.

To create a new Internet connection, open the “Network” section, then “Connection”, click the “Add” button and do the following:

“Name” - leave unchanged;
“Connection type” - this parameter depends on the authorization data from the agreement with the provider.

Choose one of the options:

PPPoE

in the “PPP Settings” block, enter “Username” and “Password” (twice);
tick the following options: “Keep Alive” - connection support, “NAT” and “Firewall”;
If desired, you can enable “PPP Debugging” - entering debugging entries over the connection and “PPPoE Forwarding”.

IPoE

check the boxes “Obtain an IP address automatically” and “Obtain DNS server address automatically”;
“Vendor ID” - if required by the provider.

PPTP or L2TP

if you need the connection to be carried out automatically, select “Connect automatically”;
“Service name” - enter the ip or url address of the authentication server;
indicate “Username” and “Password”;
in the “Encryption” line, select one of the options: “Off”, “MPPE 40/128 bit”, “MPPE 40 bit” or “MPPE 128 bit”.

3G

in the “Mode” line, select “Auto”;
authorization data is filled in by analogy with the above;
“APN” - access point name;
“Dial-up number” is the number for connecting to the operator’s authorization server.

Setting up wifi on a router d link dir 320

To set up your wireless network, select General Settings and click Enable Wireless Connection.

indicate in the “SSID” line the name of the network being created;
"Country" and " Wireless mode» - no changes;
in the “Channel” line - select either “Auto” or from 1 to 13;
if you plan to limit the number of connections to the network, enter the desired number in the line “ Maximum quantity clients."

Then open “Security Settings”.

Select one of the following options in the “Network Authentication” line:

A). "Open", "Shared" or "WEPAUTO"

b). "Open-IEEE8021X"

c) “WPA-PSK”, “WPA2-PSK” or “WPA-PSK/WPA2-PSK mixed”

Depending on your selection, enter the security key that will be required for subsequent wifi connections devices to the wireless network.

Setting up IPTV

Please note that the “IPTV” section is present only in software versions “1_3_3” and “1_4_0”.

Settings are made in the “IPTV Setup Wizard” menu

Here you only need to select the port number to which the set-top box is connected.

click "Add";
“Type” - for “IPTV” select “Transparent”;
Specify “VLAN ID” if required by the provider;
in the “Port” line, select the port number to which the set-top box is connected.

To complete the settings for the d link dir 320 router, click “Save changes”.

In version “1-2-94” there is no “IPTV Setup Wizard” section. In the Advanced menu, check if "IGMP" is enabled:

Additional features of the d link dir 320 router

As additional settings It’s worth paying attention to “WMM” (Wi-Fi Multimedia). In short, it is a protocol for prioritizing voice traffic (AC_VO), video traffic (AC_V), traffic from devices without a QoS mechanism (AC_BE), and traffic without latency and performance requirements (AC_BK) over normal traffic passing through wireless network.

“Aifsn” (variable interframe interval coefficient): the lower the value, the higher the priority;
“CWMin/CWMax” (minimum and maximum size of the concurrent access window);
"Txop" (data transfer capability);
"ACM" (Access Control Mandatory);
"Ack" (reception confirmation).

There is a big difference in the external component " web interface"There is no difference between versions "1_2_94" and "1_3_3".

However, starting with version “1_4_0”, the router interface is more similar to: the main elements can be found in the following illustrations:

This manual shows and explains in detail how to set up a Wi-Fi router D-Link DIR-320 for Beeline and Rostelecom Internet.

Let's look at the following points step by step:

How to connect DIR-320 to the Internet line and computer for setup
How to set up an L2TP connection for Beeline Internet and PPPoE for Rostelecom
How to set up a Wi-Fi password and wireless network name
Settings television IPTV(Digital TV Beeline and Rostelecom).

So, everything you might need to set up this wireless router is here, you just have to read it carefully.

How to connect a router

I’ll start with how to properly connect a Wi-Fi router to configure it, since even here there are problems.

On the back of the D-Link DIR-320, not counting the power supply and a couple of buttons, there are five ports: 4 LAN and 1 Internet. It is to the last connector that you need to connect the cable from your Internet provider.

I also note that the setup itself will be easier if you perform it from the computer that is connected to the router by wires: connect one of the LAN ports on the device to the connector network card on the computer.

And the last two points:

When setting up, the Beeline, Rostelecom or High-Speed Connection connection on the computer must be disconnected. And after you configure it, do not launch it either - the router itself will connect to the Internet.
If you are unable to enter the router settings, as described below, .

So, now you can begin the setup itself.

Logging into the settings web interface

To enter the D-Link DIR-320 settings, launch the browser and enter 192.168.0.1 in the address bar, you should see a login and password request. Standard login and password, if you have not changed them before - admin(if the password does not match, then you will be thrown back to the password entry page. It may have been changed. Then you can reset the router to factory settings by pressing and holding the Reset button for 15-20 seconds).

After entering correctly you will be at home page with basic information about the device. Click "Advanced Settings" at the bottom of the page.

Setting up D-Link DIR-320 for Beeline

To configure the connection, in the “Network” item, select “WAN”, a list of connections will open. At the bottom of the list, click “Add” and set the following Beeline Internet connection parameters:

Connection type - L2TP + Dynamic IP
Login, password - your Internet login information that you received from Beeline
VPN server address - tp.internet.beeline.ru

There is no need to change any other settings. Click “Save”, after which the page with the list of connections will open again, and at the top there will be a notification with a unit, click on it and click “Save”.

Now, if you refresh the page, you should see that the connection you just created is now in the "Connected" state, which means that the Internet is configured correctly and you can go to Wi-Fi settings networks. Do not forget, the Beeline connection on the computer must be disconnected.

On the advanced settings page, under “Network,” click “WAN.” A list of connections will open, where there will be only one - click on it, and on the next page click “Delete”. You will be returned to the already empty list of connections. Click “Add” and enter the following parameters for the Internet from Rostelecom:

Connection type - PPPoE
Username and password - Internet login data provided to you by Rostelecom

The remaining parameters can be left unchanged; click “Save”. You will be returned to the list of connections. Please note that at the top of the DIR-320 settings page the “light” is lit, click on it and select “Save”.

Please refresh the page in a minute. If you see that the connection status has changed to “Connected”, then you have done everything correctly and the Internet is already available, you can proceed to setting up Wi-Fi. Let me remind you that the Rostelecom connection on the computer itself must be disabled.

Setting up a Wi-Fi network

In order to configure the wireless Wi-Fi network settings on the DIR-320, on the page with advanced settings in the Wi-Fi item, click “Basic settings”; on the page that appears, you can set your wireless network name (SSID) instead of the standard DIR-320.

Then save these settings and return to the “Wi-Fi” item, now you should select “Security Settings”. This is where the Wi-Fi password is set. Recommended settings:

Network Authentication - WPA2-PSK
PSK encryption key (password) - at least 8 characters, without Russian letters.

Save the settings, don’t forget to also click “Save” at the top of the change indicator (light bulb). In general, the DIR-320 setup is complete.

TV setup

In order to set up digital television Beeline or Rostelecom, on the main page of the router settings, select “IPTV Setup Wizard”, in it indicate the port where the set-top box will be connected and save the settings. Connect the TV set-top box to the selected LAN port.

D-Link routers are very popular among users. Therefore, instructions for setting up, setting a password, solving some problems, etc. are always relevant. In this article, we will set a password for Wi-Fi on a D-Link router. I will show the whole process using a model as an example. D-link router DIR-615, which we configured in the article. In the instructions for setting up certain models, I always try to write about setting a password for the wireless network. But a general article for all D-Link models would not hurt.

Using these instructions, you can set a password on D-link DIR-300, DIR-615, DIR-320 and other models. Is that there? different versions firmware that differ in interface. Therefore, let's consider several options.

Regarding the issue of installing protection on Wi-Fi network, That It is necessary to set a password. And preferably during the first setup. Believe me, there are many people who want to connect. And this is an extra load on the router, low connection speed, and it’s not safe. It may even be that by connecting to your network, a third party will gain access to your files. Now, if you don’t have a password right now, you can take a look. If your network has been open for a long time, then I am sure that you will see not only your devices there.

Therefore, I advise you to come up with good password, be sure to remember it (or write it down) and protect your home network.

Instructions for setting a password for the Wi-Fi network of a D-Link router

In fact, nothing is difficult. First, go to the router settings. It is advisable to connect to the router via cable. But, if this is not possible, then you can use Wi-Fi (if any problems arise after installation, see solutions at the end of this article).

In the settings go to the tab WiFi - Security Settings (if you have English language menu, then change it to Russian). In the drop down menu Network authentication install WPA2-PSK. In the field PSK encryption key enter the password that will be used to connect to your Wi-Fi network. Just come up with a more complex one than my “123456789” :) The password must be at least 8 characters long.

In the section "WPA encryption settings" We don’t change anything, we just press the button Apply.

If your control panel is different from the one I have in the screenshot above, then you can try.

If you don't want to update the software, here's another one: instructions for installing protection on D-link with older firmware (light interface) :

In settings go to the tab Configure manually.

Then, open the tab WiFi And Security Settings.

Set a password, save the settings, and reboot the router.

And also instructions for firmware with a dark interface:

Save the settings and reboot the router.

What should I do if I can’t connect to Wi-Fi after setting a password?

A very popular problem is when, after setting a password for Wi-Fi, computers, phones, tablets, and other devices do not connect to the wireless network. On a computer, this is usually a well-known error. "The network settings saved on this computer do not meet the requirements of this network", or "Windows was unable to connect to...". Mobile devices may simply not connect.

What needs to be done. You just need to delete the Wi-Fi network on your computer, forget it, and reconnect with the password that you set in the router settings. It's very easy to do. I wrote about this in detail in this article:. If you have Windows 10, then see the instructions.

On mobile devices you just need to click on the network, hold it for a while, and select Delete from the menu.

D-Link DIR-320 is a router that allows you to organize a wireless network to connect to the Internet. Built-in firewall protects users of the entire WiFi network. The router is equipped with additional security features (MAC filter) and encryption (WEP and WPS), which minimizes unauthorized access to the access point.

Any wireless network needs protection from connection by unauthorized persons. There are several ways to restrict access to the router. The simplest of them is to set a password for WiFi. To do this, you need to connect the router to your computer, configure it, and then proceed to set a password. As an example, let's try to set a password on the WiFi D-Link DIR-320.

Quick navigation through the article

Setting a password

A password allows you to protect your wireless network from unwanted connections. To set a password, you need to connect the router to your computer (via a special cable that comes with the kit), configure it and perform the following steps:

Go to the IP address “http://192.168.0.1” (you can use a standard browser Internet Explorer, however, depending on the router firmware, the IP for connecting to the control panel may be different - http://192.168.1.1);
In the “Username” field enter “admin”;
In the “Password” line, write “admin” or leave it blank (depending on the router firmware version);
Click the “Login” button;
In the window that appears, on the left side, select the “WiFi” -> “General Settings” section;
Check the box “Enable wireless connection”;
Go to the “WiFi” -> “Security Settings” section;
In the “Encryption key” field, come up with and enter New Password(it is best to set the WPA2 encryption mode);
Click the “Change” button;
In the upper right corner of the page, select “System” -> “Save and Reboot”.

In order for a password to become reliable protection, you must adhere to the basic rules for choosing it:

The password must consist of at least 8 characters (letters of different sizes, numbers, symbols);
You cannot use first names, surnames, or animal names that may be known to unauthorized persons;
It is not recommended to use dates of births, weddings, etc.;
It is better not to use simple words and sets of numbers;
It is advisable to change your password periodically.

The Internet is an integral part of the modern lifestyle. You can access the digital web using mobile applications and Wi-Fi waves. But the quality of reception and signal level directly depends on the device carrying out the transmission, in our case the router. D-link models are most popular according to consumer requests. The most important aspect when creating an outlet to the Internet space is correct setting D-Link DIR 320.

Creating a connection between the router and computer

In order for the D-Link Deer 320 to reliably perform all tasks, it will need to be installed correctly. Usually included detailed instructions, but not in all cases. Before proceeding with the connection to the computer, you need to check its characteristics:

Open the terminal control panel.
Click on the “network status” item.
Go to the page for changing properties.
In the new menu, open the properties of the local grid.
A list of radio buttons will appear. Define "TCP/IPv4 protocol".
In the menu that appears, allow the determination of IP numbers and DNS servers automatically.
Save.

The connection is made using the wires included with the device. Among them: a cable and a five-volt power supply, a LAN cable. The router has seven functional connectors (for power, USB input, network socket, LAN sockets). Connect the cable supplied by the service representative to the INTERNET socket. Connect the wire supplied with the router to the LAN socket on the PC, and the other end to the router (this scheme is typical for a PC without a Wi-Fi adapter). If you distribute traffic via Wi-Fi waves, there is no need to use a LAN wire. Plug the power supply into a power outlet.

Video on setting up a D-Link router:

Next, to log into the Wi-Fi router, you need to launch any standard browser and enter the numbers 192.168.0.1 in the search bar. A menu will open where you will need to authorize (enter your login and PIN code). When using the router for the first time, this information is standard, name and pin code– “admin”. But if account already have it and you have forgotten the combination of numbers, click on the “Reset” button on the back panel.

Cable connection

There are several types of communication:

PPTP;
PPPoE;
L2TP.

All manipulations are performed in the device service. To adjust PPTP you will need:

Open the menu, router settings, select “Wan”.
On the next page, click on the add button.
Assign the method “PPTP dynamic IP”.
Check the box for automatic connection in the VPN section.
Specify the user's personal information (login, pin and confirmation), and mark the VPN properties. All this information is provided by the provider company that connects to the Internet. The client's data is included in a bilateral agreement with the provider. If they are missing, contact support.
Apply.
Go to the system properties of the interface and click on the “save and exit” button. The new changes will take effect.

Debugging L2TP parameters:

In the front window, under the “Network” tab, find the “Wan” value.
In the next menu, click on the add switch.
Set the type to “L2TP dynamic IP”.
Check the box for automatic detection.
Enter the owner's confidential information (nickname, code combination and confirmation), indicate VPN address server.
Go to the system section of the interface and click on the save panel. The new settings will take effect.

The method for adjusting PPPoE connection is identical to the above methods. The only difference is in the protocol. But there are also protocols PPPoE, L2TP, PPTP with a static IP address. The debugging procedure is identical for all protocols and consists of the following steps:

On the work field, under the “Network” tab, select “Wan”.
In the window that appears, confirm the addition.
Select the format “L2TP, PPPoE, PPTP static IP”.
In the ID parameters section, enter the IP address, DNS server, default gateway, netmask.
Specify user information (login, security code and code repetition).
Go to the system interface parameters and save and reboot. The new settings will take effect.

Video on setting up a PPPoE connection on a D-Link router:

Typically services with static protocols setting up D-LINK DIR 320 provided legal entities and companies, or individuals upon special request.

Access to the Internet via a USB modem

There is a USB socket on the rear panel. The router can operate by mobile internet. Such modems are produced by almost every telecom operator (beeline, MTS, megafon). To establish communication with an external adapter. You need to go to properties in the router interface. Set value USB adapter in the first section. Write the name of the telecom operator. If it is not in the default list, select the “custom” option. Fill in all the required fields with personal characteristics (user name and code), find them out from your provider or telecom operator.

Video to help with step-by-step router setup:

Go to the “USB modem” tab, go to the information section. In the window that opens, select the modem device type and wireless generation (4G, 3G, E). Allow joining mobile network Internet. Click on the action button. Some modem devices use a default password when logging in. To avoid constantly entering a password when turning it on, go to the “Pin” tab in the USB section. Enter the code provided by your provider.

Wireless connection

To change Wi-Fi characteristics, you need to go to the “network” tab and select the “ wireless transmission" In this window the user can stop wireless way traffic transmission. Specify the network authentication method.

Factory settings are not designed to encrypt information. To protect traffic from interception, specify a method other than “Open”. Create a PSK code - this is the password that will be requested when finding a Wi-Fi network.

Software update

It is recommended to constantly monitor for new updates and install them. Each update adds new features to the router and increases the level network protection from unwanted hacking. In the “support” tab you can find the latest current version BY.

To update the device software, you need to go to the “system” section and open the “update” section there software" A window will appear in which you need to click the “browse” button. Specify the path to the current firmware file, which is located on your computer (downloaded in advance from an Internet resource).

Establishing a Wi-Fi connection

When all the required settings have been made, the last stage of adjustment begins. On PC with operating system Windows 7 order is as follows:

On the right side of the taskbar is the “Internet access” icon. Click on it.
A window will open showing all detected nearby wireless internet distributions. Click on the appropriate channel.
Click on the “connection” icon.
If a security code has been set, you must enter it.

After completing these steps, you will have access to the Internet.

Conclusion

Having completed the required debugging, the device will perform all its functions correctly. The process of setting up a router is quite labor-intensive, and not every user is able to cope with it. Therefore, when drawing up an agreement with a provider, he provides a specialist technician who will configure the router for high-quality operation.